Archives for 

Heating

Ways to Get Smart About Central Heating

You may not believe it, but if you upgrade your home or office space from using an electric storage heating system to a central heating system, you can actually save considerably on your monthly electricity bill! And even better is that, contrary to popular belief, converting from central heating should be relatively easy if you are able to find a reliable and experienced expert central heating installer. The key is to make sure you’re able to communicate the requirements and specifications of your home clearly so they can provide a quality proposal.

If you have been wanting to convert to central heating system but have wanted to know more about it, read on to learn more about how you can get smart about the central heating system you install in your home.

 heating repair

Things to consider when you decide to convert to central heating

  1. You need to figure out what kind of boiler you want to use.
  2. You need to choose from a wide variety of options available for a radiator. Styles and sizes greatly vary, so there’s bound to be a radiator that’s perfect for the heating requirements of your home!
  3. You need to figure out how easy or complicated the installation of your new heating system will be, as this will determine if you’ll need to temporarily move out of the house or if you can stay while the installation is taking place. The most important factor in deciding this is how easily or complicated the laying of the copper pipework will be.
  4. The size of the space will also affect the length of time of the installation. For example, a house or building with two floors would take a team between two to five days to finish a central heating system installation.

 heating repair

Different tips and tricks to make your new central heating system more efficient

  1. If your house or office takes up a considerable amount of space, heating the entire place will obviously cost more than it would to heat an averaged size home. But you can lower your electricity cost if you implement zoning for your heating. If you are able to control the heat that is produced for different parts of your home, you’ll be able to make your heating system much more energy efficient. For instance, if at certain times of the day, only one floor of your home is occupied, a zoning setup for your central heating system will allow you to provide heat only in the occupied floor. This also applies if you decide to make different rooms of your home into different heating zones, letting you provide heat to only areas where it is needed.
  1. Choosing to have intelligent controls such as a thermostat installed is also an ideal way to make your central heating system more efficient, especially if you install heater for different spaces in your home or office, allowing you to control the temperature in different areas. A room thermostat is an easy way to make your central heating system work smarter and be more efficient.

 

DIY Troubleshooting Tips To Repair Heater

Space heating makes up 45% of any home’s electric bill. With such a significant cost impact, it is crucial to make sure that your heating system works as it should at all times. However, the costs related to running a heater can quickly shoot through the roof.

The reality is that your furnace will suffer from breakdowns and even stall at some point. Not all these cases need the services of a heating repairs expert.

Save on the amounts you spend on your furnace with these DIY troubleshooting tips to repair heater.

Problems With The Heater’s Filters

The majority of the issues that affect heating systems are traceable to filter issues. The furnace filters function to keep debris and other impurities from getting released out to the home. Filters are one of the heating system’s parts that wear out quickly based on their function.

 heating repair

You can clean out the filters according to the manufacturer’s instructions or get online to find out how to do it. Change the filters every other month or once a month, depending on your heater’s frequency of use.

Pilot Light Issues

The heater’s primary role is warming up cold air and releasing it around the home. The pilot or ignition light plays a crucial role in this process. It may keep going off owing to drafts, and you can fix heater problem by relighting it.

The burner needs to emit blue flames at all times. If it emits yellow lights, it indicates that there is a venting problem. You can try to clean out the burner to see if it fixes the issue. Inspect the burner for signs of corrosion as well. Make sure that the furnace burner works as it should with the fan on as well as when it is off. However, for such a heater problem you need to call in the heater repair experts.

Heater Repair Tips For Heat Register Issues

The heat registers release out the warm air around the house. If the heat registers feature obstructions, it prevents them from evenly distributing heated air throughout the home.

Cleaning out the heat registers all around the house makes sure that heated air gets out through them as needed. It is also important to remove any furniture and rugs placed over heat registers. It helps to allow heated air to get through them and ensures even heating throughout the house.

Thermostat Problems

The thermostat works as the brain of your heating system. You input temperature settings, and the thermostat communicates with the furnace to offer the desired heat levels. The thermostat may fail to work because of some issues.

 heating repair

For older thermostat models using batteries, try to change the battery and see if it solves the problem with a thermostat that won’t power on. Thermostats that do not maintain temperature settings or fail to relay the same to the heater often have technical issues. Once again, you need the services of a heating expert to fix such an issue or replace the thermostat. 

Before undertaking any heater repairs process, turn off the furnace and gas supply.

 

Common Heater Repair Problems

A well-maintained heating system is a necessity for every home. Thanks to technological advancements, the current heating systems are quite different from the older systems which most homes still have. If you didn’t know, modern heating units are extremely efficient, energy efficient, quieter and relatively smaller. What’s more, there are lots of options regarding the heating source. A heating system can operate on gas, steam, electricity, and can also run on eco-friendly fuel sources such as solar, water and wood pellets.

How does a central heating system functions?

A central heating system contains a primary heating component such as a boiler or furnace usually installed in a hidden area such as a basement or garage. Its principal function is to distribute heat throughout your entire room by typically pumping warmed air via a system of air ducts or by sending steam or hot water through pipes to either convectors or room radiators. It is imperative to note that both gravity and forced-air heating systems are equipped with at least one thermostat which turns the cooling/heating unit on and off, regulating the temperature of the room appropriately.

 air conditioner repair adelaide

Homes that do not have the central heating usually use electric baseboard heaters, in-floor or in-wall gas heaters. Ducted air systems are perhaps the most common types of cooling and heating in many homes.

What are some of the most common heater problems?

Despite their effectiveness as well as the advantages, these fantastic home devices are always prone to some common problems. Bearing in mind that your heating system is an essential device for your home, efforts must always be made to ensure that it remains in its most perfect condition. But, when it develops any problem, it should be only handled by an experienced heating repair melbourne technician.

  1. The blower runs continuously: Typically, two factors may cause your fan to run in a continuous manner. These are the limit switch or your thermostat. The limit switch is often located on the furnace, and it shuts off the heater when the air in the plenum becomes extremely hot. You’ll have to examine the thermostat to see if the Fan switch is on. If it is on, just turn it off or put it in auto mode. However, if it is already set to Auto or off but the blower is still misbehaving, just know that you’ll have to adjust the furnace’s limit switch.
  2. The furnace fails to blow air: If the motor of your furnace is functioning, but the blower cannot circulate air, then probably the belt which connects the two is the culprit. The good news is that replacing it is often easy and straightforward. First, you’ll have to disconnect the power to the system plus the gas at the gas valve which serves your furnace. Access the broken blower by removing the closure on the front of the heater cabinet. Confirm the number stamped on the belt before getting the exact model for replacement.
  3. The furnace is turning on and off regularly: This particular issue is often caused by a faulty thermostat. It will be even more common if yours is a combustion heater. If the thermostat has a particular lever which goes round a calibrated scale which is indicated LONGER you can try resetting this. It may take you several attempts and hours before you restore the thermostat to its original setting. However, if the adjustments cannot help solve the problem, you may consider replacing your thermostat altogether.
  4. The furnace does not heat: Studies tend to show that thermostat malfunctions are arguably the most common heating system failures. Of course, there are other possible causes including a tripping circuit breaker and blown fuses. You can check and ensure that the thermostat of your heater is set to HEAT, especially if yours is a cooling and a heating unit. Also, ensure that the circuit breaker of your furnace is on and running or the fuse has not blown out. Confirm if both the main electrical panel as well as the subsequent sub-panels which provide power to your unit is working. You may reset your circuit breaker or replace the broken fuse. If all these do not help solve the problem, you’ll have to contact your local electrician for more assistance.
  5. A noisy ductwork or furnace: Bearing in mind that a significant number of heating ducts are made of metal, they usually conduct sounds quite easily from the air-handling system. To help prevent this typical problem, you can consult your heater technician and instruct him to break the conduction of sound. This can be achieved by inserting a flexible insulation ductwork between your furnace and the ductwork. However, if your device produces grinding sounds, you’ll have to shut off your heating system and call your local furnace repair technician for assistance. This often indicates that the motor bearings are probably shot.

 heating repair brunswick

Your heating system is a critical component of your home. Proper maintenance and routine repairs are crucial to ensuring that it remains in its peak condition at all times. As always, you must always ensure that you only seek the help of a qualified technician to handle it.

How to Clean Your Heater

  Among the preparations you need to make at the onset of winter is making sure that your heating option will work smoothly and efficiently as the days and nights grow colder. To ensure this, you’ll need to make sure your heater is clean and ready to operate for an entire season after being dormant […] Continue reading →

Knowing your heat pump compressor

The compressor is often considered the most crucial component or the heart of a heat pump because of its unique functionality to circulate the refrigerant in the entire system and form a heat exchanging cycle. Modern compressors have never been quieter and more efficient than.   But when the compressor fails to work, the entire […] Continue reading →